Rugby PREMIUM CEMENT
Dri Wall Adhesive
Bonding Coat
Browning
- Lighter colour, ideal for use in all applications ---------where colour is important.
- For use in concrete, mortar, render and screed
- Reduced admixture requirements in mortar
- Improved workability, cohesion, finishing and ----------resistance of --hardened mortar or concrete to --------freeze-thaw attack
- Consistent, convenient and cost effective
- Chromium (VI) compliant – Intended to reduce the --risk of allergic contact dermatitis.
ALSO AVAILABLE IN 100% WATERPROOF PACKS!
A general purpose gypsum-based adhesive. For use on high, medium or low suction backgrounds.
Thistle Bonding Coat is an undercoat plaster ideal for smooth and low suction backgrounds, including:
- Dense blocks
- Concrete
- Plasterboard
- Backgrounds pre-treated with ThistleBond-it ----------bonding agent.
An undercoat plaster for solid backgrounds of moderate suction with an adequate mechanical key.
Multi Finish
Dri Coat
Board Finish
This versatile final coat plaster provides good results on all suction backgrounds, and is therefore the best choice for plastering where both undercoats and board backgrounds are involved on the same job. It is also ideal for small jobs and patching.
A cement-based undercoat plaster for re-plastering after installation of a damp-proof course.
The ideal final coat plaster for low-medium suction backgrounds such as plasterboard and Thistle Dri-Coat.
Standard boards
Suitable for most applications where normal fire, structural and acoustic levels are specified. Suitable for direct decoration or Thistle plaster finish. Available in tapered edge or square edge as shown below.
Characteristics
- Ivory face paper
- Brown reverse side paper
- Available in square edge
- Complies with EN 520 – Type A
- Thermal conductivity 0.19W/mK
Available Sizes
9.5mm Board
Width Length (mm)
900 1200 (4 x 3 x 3/8")
900 1800 (6 x 3 x 3/8")
1200 2400 (8 x 4 x 3/8")
12.5mm Board
Width Length (mm)
900 1800 (6 x 3 x 1/2")
1200 2400 (8 x 4 x 1/2")
FireLine boards
Plasterboard with glass fibre and other additives in the core.
Used in partition, wall lining and ceiling systems to give increased fire protection. Also used for protection to structural steel.
Characteristics
- Pink face paper
- Brown reverse side paper
- Available in square edge
- Complies with EN 520 – Type F
- Thermal conductivity 0.24W/mK
Available Sizes
12.5mm Board
Width Length (mm)
900 1800 (6 x 3 x 1/2")
1200 2400 (8 x 4 x 1/2")
Vapour boards (Foil Back boards)
Plasterboard with with an additional laminated vapour control layer.
Characteristics
- Foil face paper
- Brown reverse side paper
- Available in square edge
- Complies with BS 1230 Type 2 and 6 and BS EN 14190.
Available Sizes
9.5mm Board
Width Length (mm)
900 1200 (4 x 3 x 3/8")
12.5mm Board
Width Length (mm)
900 1800 (6 x 3 x 1/2")
SoundBlock boards
Plasterboard with a higher density core.
Designed for use in wall and partition systems where greater levels of sound insulation are required.
Characteristics
- Pale blue face paper
- Brown reverse side paper
- Available in square edge
- Complies with EN 520 – Type D
- Thermal conductivity 0.25W/mK
Available Sizes
12.5mm Board
Width Length (mm)
900 1800 (6 x 3 x 1/2")
Moisture Resistant boards
Plasterboard with water repellent additives in the core, encased in a special green liner paper. Suitable for intermittent moisture applications.
Characteristics
- Green face paper
- Green reverse side paper
- Available in square edge
- Complies with EN 520 – Type A, H1
- Thermal conductivity 0.19W/mK
Available Sizes
12.5mm Board
Width Length (mm)
1200 2400 (8 x 4 x 1/2")